Inventory


  • #RE10109 Casting #N/A
    CAT C12
    CAT C-12 ENGINE BLOCK Packaged and ready to ship *635lbs * Machined and ready. Here is what was done to it: -Cleaned and checked out -Surfaced .006@ -Cut counter bores -Replaced 3 caps -Align bore block -Performed final clean up -Installed cam bearing -Replugged.
    Condition: New

  • #RE10112 Casting #9N3758-2
    CAT 3208 NAT
    CATERPILLAR 3208 NAT BLOCK NEEDS ALIGN HONE, BORE .020, AND MAGNAFLUX CONDITION IS GOOD. @.
    Condition: Used

  • #RE10114 Casting #85517
    ISUZU EX120
    ISUZU EX120 BLOCK GOOD CONDITION, NEEDS MACHINING. @.
    Condition: Used

  • #RE10116 Casting #7N5454
    CAT 3304
    Block has been machined Cut for shim CAT Part number: 104-5518 and it will need 4 Surfaced 0.006@ 1 Lower repair * This block will still need the cam bearings installed, the balance shaft bushings installed, and the oil galley plugs swapped over from the block it is replacing..
    Condition: Used

  • #RE10117 Casting #1820494C4
    INTERNATIONAL DT466
    INTERNATIONAL DT466 BLOCK NEEDS PARTS. LOW PRICE. GOOD CONDITION..
    Condition: Used

  • #RE10118 Casting #1820494C4
    INTERNATIONAL DT466E
    International DT466E Block@ **Needs surface, counter bore, and align hone.
    Condition: New

  • #RE10124 Casting #R63198
    JOHN DEERE 6466
    JOHN DEERE 6466 BLOCK GOOD CONDITION, NEEDS MACHINING. @.
    Condition: Used

  • #RE10125 Casting #R63198
    JOHN DEERE 6466
    JOHN DEERE 6466 ENGINE BLOCK @.
    Condition: New

  • #re10131 Part #8N9625
    Casting #8N9625
    CAT 3406B
    CAT 3406B ENGINE BLOCK Block casting #:8N9625 * Surfaced .008@ Sleeved 1, 5, @ 6 New cam bearings Ready to ship.
    Condition: New

  • #RE10133 Part #68321868
    Casting #68321868
    CUMMINS QSB 3.3
    New Long Block Cummins QSB 3.3 80hp@2400 rpm Includes: Block, cylinder head, valve train, front gear, front main, rear main, water pump. READY TO SHIP..
    Condition: New

  • #RE10165 Part #468BH2U481760
    Casting #468BH2U481760
    INTERNATIONAL DT466B
    International DT466B **Needs surface,weld #4, and align bore** International DT466B@.
    Condition: Used

  • #RE10167 Part #60.6.15
    Casting #60.6.15
    ISUZU E120
    ISUZU E120 CRANKSHAFT@ GOOD CONDITION, NEEDS MACHINING. @.
    Condition: Used

  • #RE10171 Part #25/3C1
    Casting #25/3C1
    INTERNATIONAL DT466E
    INTERNATIONAL DT466E CRANKSHAFT Visual inspection:rust pitting on #7 Main Seal surfaces:OK Bend:0.001@ Mains:3.5352@(STD) Rods:3.1501@(STD) Thrust:1.709@(STD) Stroke:5.352@ M Radius:uc R Radius:uc T Radius:uc Hardness:55RC Gear cond.:OK, oil pump drive gear will be removed Casting #(s):3C1 Removed oil pump drive gear, polished, cleaned, and bagged..
    Condition: Remanufactured

  • #RE10173 Casting #E106
    ISUZU E106
    ISUZU E106 CRANKSHAFT POLISHED, GOOD CONDITION, NEEDS SOME WORK. @.
    Condition: Used


  • |<  <   ... 11 12 13 14 15    >  >| Pages: 13 of 15

CONTACT US

  = five - seven (please enter the answer to the question or statement)